W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

Model NO.
W1B
Specification
20 KGs per bag
Origin
China
HS Code
3901909000
Production Capacity
20000 Tons Per Year
Reference Price
$ 0.81 - 0.90
Contact Us

Product Description

Characteristic:   This product is ethylene elastomer with functionalized MAH which is especially suitable for super-tough or cold-resistant nylon.
Product Model W1B
Appearance White or light yellow even granules
Melt Index(190°C,2.16Kg):g/10min 0.8-2.0
Grafting Ratio High
Density(g/cm3) 0.86
Application
1.Be used for PA6 or PA66 compatibilizing or toughening. Increase the impact resistance and processability of nylon, decrease the water absorption, greatly improve the cold-resistance.
2.Be used for the compatibilizer of nylon and polypropylene/polyethylene alloy.
3.Be used for the macromolecular modifier(coupling agent) of mineral filled or glass-fiber filled nylon.
 
Comparison parameters of different applications :

Table1:Typical Data of Toughening of PA6 Resin
Performance Unit PA6 PA6+15%W1B PA6+20%W1B
Tensile strength MPa 60 55 47
Flexural strength MPa 90 80 70
Lzod notched impact strength (23ºC) J/m 80 750 950
Lzod notched impact strength (-50ºC) J/m <=5 220 275

Table2:Typical Data of Toughening of PA66 Resin
Performance Unit PA66 PA66+15%W1B PA66+20%W1B
Tensile strength MPa 75 53 47
Flexural strength MPa 102 59 55
Lzod notched impact strength (23ºC) J/m 80 600 900
Lzod notched impact strength (-50ºC) J/m <=5 180 270

Table3:Typical Data of Reinforcing and Toughening of PA6 Resin
Performance Unit PA6 PA6+30%GF+6%W1B
Tensile strength MPa 60 135
Flexural strength MPa 90 195
Lzod notched impact strength (23ºC) J/m 80 250

Table4:Typical Data of Reinforcing and Toughening of PA66 Resin
Performance Unit PA66 PA6+30%GF+6%W1B
Tensile strength MPa 75 150
Flexural strength MPa 102 215
Lzod notched impact strength (23ºC) J/m 80 220
Note: The data above are all experimental typical values, only for reference .

Cold - resistance test data :
Izod  Notch ed   I mpact S trength J/m
Ingredient 23°C -40°C -50°C
PA6+15%W1B 760 278 260
PA6+20%W1B 900 880 538
PA6+25%W1B 1020 970 662
As can be seen from the above figure, the product has a good low temperature   toughening effect on nylon between -40 and -50, and the notch impact rejection rate at low temperature is very high.

Recommended dosage:
5-25%, which can be increased or decreased in moderation according to the toughness requirements, taking into account the cost. PA6, PA66 reinforced and toughened (3-10%), the phase of nylon, polypropylene, polyethylene blended gold   Container (3-10%).

Pack ag ing and Storage:
20KG kraft paper bag with internal plastic bag, This product shall be treated as non-hazardous article and be stored or transported under dry conditions, avoid sunlight and rain.

Other POE-g-MAH series List:
Brand number
  		Melt index
190ºC 2.16kg
g/min 		Grafting ratio
  		Density
g/cm² 		Characteristic
 
W1A 0.3-1.0 High 0.87 PA reinforced filling, ultra-low temperature toughening.
W1A-2 0.3-1.0 High 0.87 PA reinforced filling, ultra-low temperature toughening.
W1A-4 0.1-1.0 High 0.87 PA reinforced filling, ultra-low temperature toughening.
W1A-6 >0.1 High 0.89 PA reinforced filling, l ow temperature toughening.
W1A-F 5-14 High 0.87 PA reinforced filling, TPE encapsulated
W1B 0.3-2.0 High 0.87 PA reinforced filling, ultra-low temperature toughening.
W1 0.2-1.0 High 0.88 PA reinforced filling, low temperature toughening.
W1C 0.3-1.5 Medium 0.88 PA reinforced filling, low temperature toughening.
W1D 0.6-2.0 High 0.88 PA reinforced filling, low temperature toughening.
W1F 10-24 High 0.87 PA reinforced filling, h igh dispersion.
Note: The above data are typical values tested and should not be construed as specifications
Low < 0.4 wt %, Medium 0.4 - 0.8 wt %, High > 0.8 wt %.
 
Application display
W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

Company profile
Coace Chemical Company Limited is located in Xiamen Special Economic Zone, China. It is a national high-tech enterprise integrating R&D, production and sales of polymer materials, specializing in R&D, production, sales and service of plastic compatibilizers and toughening agents.
For more than ten years, the company has been adhering to the business philosophy of "stable quality, refinement and globalization", serving the market, the factory owns 50,000 square-meter area and nearly 100 employees, including 20 technical R&D personnel, and is equipped with eight modern extruding-pellets systems production lines, which ensure the annual capacity of ten thousand metric tons. The products cover compatibilizers, coupling agents, impact modifiers, and other functional additives. and obtained ISO9001 quality management certification, with an annual production capacity of 20,000 tons.
W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

Our factory


W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature
W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

Our certifications

W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature

Exhibitions

W1b Poe/Obc-G-mAh/mAh Grafted Poe Used as Compatibilizer for Polyamides/ Nylon/PA Toughening in Low Temperature Our advantages

1.Research & Development strength.
2.Quality assurance.
3.Product customized.
4.Lower costs and more convenient cross-boarder trader.
5.Delivery on time and global service.
 
 

 

Plastic Auxiliary Agent

SUPERAUTO.CAT, 2023